• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up a doorway Up a Door

The act of boarding up service up a door is one way to protect vacant investment properties from the elements. While it may not be able to prevent all destruction, it can help avoid some of the problems that come with severe storms.

boarding up windows and doors (simply click the following article) can deter trespassers and vandals as well as squatters. However, it can be expensive and time-consuming to set up plywood boards over the openings on a house.

Measure the Door

The first thing you'll need is tape measure. You might also want to have a ladder or chair handy in case you need to see more clearly at the top of the frame. Wear gloves and protective glasses when you use these tools.

Once you have the measuring tool, start by taking the door's width measurement. This can be done by running the tape measure horizontally across the door. Be sure to take out all extra parts of the door, like the sweep, when measuring. Then, take a measurement of the height from the floor to the existing sill or lintel. It is essential to measure in multiple places especially for older doors, because they may not be a perfect rectangle. If the measurements are different, use the largest number.

After you've logged the measurements of height and width, you'll need to figure out what size boarding you need for the frame. It should be at minimum 2 inches wider and 1'' taller than the door. 2'' higher. This will give you plenty of space to move the frame and door to fit.

It's a great idea remove the trim or casing around the jambs of the door in order to observe the studs. This will enable you to take measurements of the exact gap between the frame's studs and the edge.

After you have removed the trim, measure the width of your door frame using the tape measure. The frame should be measured at three different locations and use the smallest measurement. Also, you should determine the height of the frame from top to bottom, on both sides. Make use of the shortest measurement for the width of your door.

If you're having difficulty with the measurements, you should seek out a professional who will come to your house and conduct the measuring. They'll tell you the size and style of door you need and how to prepare your frame to accommodate a replacement door.

Plywood can be cut into pieces

A door frame is generally composed of a series of thin boards or studs which create a hollow space surrounding the door. Two hinges are attached to the studs and hold a typical door in place. This means that, if you wish to restore the door, it's important to remove the hinges off the door for a night. To keep insects out of your home and to secure the door's opening, a straightforward method for boarding doors is to place plywood inside the opening. This is easy to do without the need to screw or nail the plywood to the door frame.

Plywood is inexpensive, easy to work with and looks great when it is completed. This makes it the ideal material to provide an interim solution to an issue that requires the removal of an existing door while renovating or installing a brand new one. It is also a great option to secure the opening in a room that is being renovated, like an unfinished basement, or a construction site.

Start by measuring the width of the door opening as well as its height. Draw the dimensions on the plywood using a utility knife and a drywall square or other straight edge made of metal. Then, you can snap the chalkline along each line to indicate where to cut. Utilize a circular saw to cut the plywood to size.

When cutting the plywood it is essential to protect your eyes and ears. Wear earplugs or goggles that are protective whenever possible. It is also important to use a sharp blade with a lot of teeth, which will permit you to cut quickly and without any tear-out. Utilize a small piece of wood to guide the blade. Hold it about a hair's breadth away from the mark when cutting.

Attaching a pair of shorter braces to each end is a good way to secure the plywood in place without screwing it into studs. Place one brace inside and the other outside of the door. Then, insert two 1-1/2-inch deck screws in each of the holes, and tighten them using an open-end wrench.

Fix the Plywood

When you have a piece of plywood cut to the appropriate size and with holes for Boarding Up windows and doors rails and stiles predrilled then it's time to fasten the panel to the frame. This is a relatively simple project that does not require extensive carpentry skills, as long as you follow the correct procedure and use the proper tools.

Set up a table near the entrance, with two sawhorses at each end, and framing lumber 2x4s. Use the marks made during the measurement procedure to guide you in cutting the plywood. Utilize a utility blade and a straight edge of metal to score the lines. This will serve as a guideline for the saw blade, and will help prevent splintering when you cut the plywood.

Wear eye protection and cut along the lines of scoring with a circular saw or boarding up windows and doors table saw equipped with a fine-tooth blade. Then sand the edges of the plywood panel using 120-grit sandpaper. This will smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding process, apply a coat of wood sealer on the plywood panels and allow to dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using T hinges, make holes in the outside of the door to accommodate the strap portions of the hinges. Then, you can screw the hinge's outside edge to the frame using a screwdriver. Repeat the process on the inside of the door service for boarding up windows the remaining hinges, being cautious not to tighten too much on any of them, or the hinge could shift.

If you have only a single hinged outside door you can make it easier for the latch to close by placing a wire through the loops of the exterior hinges. Fold a small piece of tie wire in half, and then put it through the two holes on the exterior of the door. Then, you can twist the wires together and secure the door.

Install the Plywood

Based on the measurements you have taken and place the plywood into the door opening. Move the frame's header (top) and the sill. Use a level to make sure there's no slop in the header or sill. If the level isn't quite right then place another shim if it is needed and continue the process until the sill and header are level.

Once the plywood is in place, secure it using the stainless-steel hinge bolts and wingnuts. It's a good idea to use a screw gun with an hex-head attachment so that you prevent stripping the head of the screws.

While you're at it, should your home be constructed with studs that run through the doorway's height, drill hanger bolts through the plywood and into each framing stud. This is much simpler than using a drywall cutter to create the hole.

After putting the plywood in place, measure the width and the height of the door opening. If necessary, cut your bottom of the plywood to match the height the door frame. Cut two pieces of framing lumber 1 by 6 to serve as braces for the upper and lower edges. Cut along the lines that are marked on your plywood with circular blades with fine-toothed teeth. Wear eye protection. Splinters can be removed from cuts using a sanding tool.

Once you've got the braces set attach each one to the plywood with pairs of finishing nails 2 inches long. Counter-sink all nail heads when you're done. Cover the braces and plywood with a good wood sealer such as this wipe-on polyurethane by Minwax.

If your door is too big it is possible to add decorative molding to fill in the gap between your door and jamb, or you can reduce the size of your opening. However, in most situations, it's more affordable and simpler to just choose an alternative door. This also eliminates any headaches that you might have faced with the original door if it was damaged and could no suitable for the opening.